NEXQ6GO-M Cellular WiFi Router

About this Item

Equipped with MHF4 Connector Pigtails (for M.2 modems) and WiFiX firmware preinstalled.



WiFiX NEXQ6GO-M Cellular Router

The WiFiX NEXQ6GO-M cellular router is the newest router and comes with our WiFiX version of GoldenOrb firmware preinstalled on the router. The latest version, if newer than that installed on the modem can be found here:

Note: The NEXQ6GO-M has a different architecture than the WE826-T2.  The NEXQ6GO-M uses the Qualcomm Atheros QCA9533 v2 where the WE826-T2 uses the MediaTek MT7620A chip.  While similar in appearance, they are two different routers and the WiFiX firmware for each of these routers ARE NOT compatible with the other.

The NEXQ6GO-M and WiFiX firmware were designed to produce a moderately more stable 2.4GHz WiFi component with a noticeable increase in throughput–a theoretical transmission rate of 300Mbps.

We are offering two versions of the NEXQ6GO, the NEXQ6GO-U and the NEXQ6GO-M This will help our customers from having to separately order different pigtails in order to use a modem with a different type of connector ports.

The “U” version is equipped with U.FL connector pigtails for use on a Mini PCI-E modem (i.e., MC7455, EC25-AF, EP06-A…). 

The “M” version is equipped with MHF4 connector pigtails for installing a M.2 modem (i.e., EM7565, EM7511, EM12-G, EM06-A….).   A Mini PCI-E to M.2 adapter is required for a M.2 modem, and comes with this router as a bundled item (see below). 

This listing is for the “M” (for use with M.2 modems) version. If you want the “U” version (for use with mPCIe modems), go to the NEXQ6GO-U page.

The NEXQ6GO-M is a router and requires a modem for cellular internet.  See below for different modem options.

Please refer to our Tutorial for instructions configuring the WiFiX firmware/software for cellular service.

NOTE: Cellular service providers may require activating a specific data plan to use on a cellular internet device.   The carriers are constantly updating and/or modifying existing cellular plans.   It is the customer’s sole responsibility to assure a compatible cellular plan is available prior to purchasing cellular related components.



Our WiFiX NEXQ6GO-M routers include a 2 Amp Power Adapter after determining that 1 Amp is insufficient when using the Sierra Wireless MC7455 modem under load–which may result in both WiFi and service disconnection issues. 

We strongly recommend upgrading to our top quality 12V 4A (30W) power adapter when using the Sierra Wireless and/or Quectel CAT12/CAT20 modems.   The importance of providing adequate power to the router and its modem must not be underestimated.



The SIM card slot on the router uses a Standard sized SIM card, and a SIM Card Adapter Kit may be also be required.  See installation tips below to avoid damaging the SIM Card slot.



The NEXQ6GO-M is equipped with a single Mini PCI-E modem slot which allows modem installation without additional hardware.

When installing a M.2 form modem into a Mini PCI-E modem slot, a Mini PCI-E to M.2 Key B adapter MUST be used (with or without optional SIM Card slot). This can be selected as an add on for this listing. If you do not see the add on, you must add it by following the link mentioned previously here.

Refer to the steps at the bottom of this listing for instructions on installing a Mini PCI-E and M.2 modem.


Want to see our modems? Look here: Mini PCI-E Modems and here: M.2 Modems


The Mini PCI-E modems have U.FL antenna connector ports and require two (2) five inch U.FL to SMA Female Bulkhead pigtails to install in the NEXQ6GO-M.

The M.2 modems have MHF4 antenna connector ports and require two (2) five inch MHF4 to SMA Female Bulkhead pigtails to install in the NEXQ6GO-U.


1. The MC7455 is not recommended for Sprint Band 41 (unless provisioned via Sprint) as it may experience random disconnects.



The NEXQ6GO-U stock cellular antennas may be upgraded to any of the following cellular antennas:


A significant number of customers like upgrading their stock antennas with the Cisco LTE Omni Antenna Kit.

The Cisco antennas use TNC connectors (as opposed to SMA).  The NEXR5GO antenna pigtail cables must be upgraded to match that of the modem’s antenna connector ports to install the Cisco antenna upgrade:

  • The Mini PCI-E  modems (see above) require two U.FL to TNC Female Bulkhead connector pigtails, one 5 inch pigtail and one 10 inch pigtial to install the Cisco antenna kit.
  • The M.2 modems (see above) require two MHF4 to TNC Female Bulkhead connector pigtails, one 5 inch pigtail and one 10 inch pigtail to install the Cisco antenna kit.

* Note: The two existing SMA connector cutouts in the NEXR5GO router case must be enlarged/drilled to 15/32″ to accommodate the larger TNC bulkhead connectors.



See this LTE FIX IT tutorial for complete instructions configuring WiFiX firmware.

See this LTE FIX IT tutorial for general information on building and configuring an LTE router and modem.



The WiFi supports IEEE802.11 N/G/B/A protocol with a maximum wireless rate of 300 Mbps.  It is equipped with two (2) removable RP-SMA 5dBi high gain WiFi antennas for better coverage and performance in  large areas.

Some users for home installations for family/multiple users/devices, may discover the NEXQ6GO is best used strictly as the modem/gateway (to provide the internet) and connected to a quality dual band (2.4/5GHz) WiFi router or Access Point to provide the WiFi component.  The NEXQ6GO would be then be connected via an Ethernet cable from one of the LAN ports on the NEXQ6GO to the WAN port on the WiFi router or Access Point.



Our WiFiX version of GoldenOrb (based on OpenWRT) comes pre-installed on the NEXQ6GO which may be easily flashed to other custom OpenWRT based firmware. 



It is important to insert the SIM Card into the router correctly to avoid bending and/or damaging the internal pins and spring in the router’s SIM Card Slot.

It is equally important when using a SIM Card Adapter, that the SIM Card is properly seated into the adapter to avoid damage to the SIM Card slot components.  

DISCLAIMER:  Damage to the SIM Card slot, its spring and pins, are NOT covered under warranty.

See below for proper SIM Card and Adapter preparation and installation.


The SIM Card installs into the NEXQ6GO with the metal surfaces facing up.  The cut corner of the SIM Card is inserted into the SIM Card Slot.



When using a SIM Card Adapter, the SIM Card MUST fit correctly into the adapter.  This will:

  • Help prevent damaging the SIM Card Slot internal components, and,
  • Help to eliminate disconnect issues that can occur when the router warms up to operating temperatures.

To assure the SIM Card is seated into the SIM Card adapter correctly, all the tits/tabs on the four sides of the SIM Card MUST be removed.  This is accomplished by laying an Emory board or fine piece of sand paper flat on a table and gently working each side of the SIM Card back and forth to sand off the tits/tabs.

The SIM Card should fit into the adapter with ease, not loose but not tight.  Otherwise, when pushed into the router, the SIM Card can tilt ever so lightly on one end (or side), causing damage to the pins in the SIM Card Slot and/or the pins not making adequate contact with the electronic contact chip.  This bad connection can worsen as the router warms up.

Check the SIM Card closely for any signs of damage.  If SIM Card is bad, worn or dirty from swapping it in and out of devices, clean the SIM Card’s electronic metal chip with an alcohol pad and refrain from touching the metal chip area during re-installation.  A pencil eraser may also be helpful to gently clean the metal contact scratches.




Chipset Qualcomm Atheros QCA9533 Ver 2
Protocol IEEE802.11b/802.11g/802.11n/802.3/802.3u
Wireless speed 2.4g 300Mbps
WiFi frequency 2.4GHZ
Antennas 2 x 2.4GHz WiFi
2 x 700-2700 Cellular
Interfaces: 1*PCI-E slot
1*SIM card slot
1*USB 2.0 port
1*Micro SD card slot
1*10/100M WAN port,support Auto MDI/MDIX
4*10/100M LAN port,support Auto MDI/MDIX
LED Power,PCIE module indication light,2.4G,WAN,LAN1,LAN2,LAN3,LAN4
Button 1*Reset button
Power adapter DC 12V/2A
Max Power consumption < 12W with no modem
Product size(L*W*H) Size:130*82*34MM
Color Black
Software WiFiX version of GoldenOrb
WAN Type PPPoE,Dynamic IP, Static IP,3G(4G)dial-up
Work Environments Operating Temperature:-30℃ ~ 70℃;
Storage Temperature:-40℃~ 70℃;
Operating Humidity:10%~90% non-condensing
Storage Humidity:10%~90% non-condensing
Certification CE,FCC & RoHs
Packing box Size265*150*46MM
Net weight 0.46 KG
Gross weight 0.75 KG


Tutorials - Firmware

WiFiX Router Firmware

Firmware Update Tutorial for WiFiX NEXQ6GO Routers


There are no reviews yet.

Be the first to review “NEXQ6GO-M Cellular WiFi Router”

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Questions? Comments?

Leave Your Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.

90 Day Warranty: 90 Days